歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-常見問題

常見問題

全自動超聲波清洗機在工作時對溫度的要求

作者：admin來源：http://www.ks785.com/時間：2021-01-25

超聲波清洗機溫度設定:按加熱ON鍵,再按加熱OFF鍵,根據您所需要的操作溫度按下設定鍵“上”或“下”,設定鍵允許所希望的操作溫度在10℃-80℃之間。每按一次表示設定加熱溫度增或減1℃,一般工件清洗要求水溫在60℃左右。

Temperature setting of ultrasonic cleaning machine: press the heating on key, and then press the heating off key. Press the setting key "up" or "down" according to the required operating temperature. The setting key allows the desired operating temperature to be between 10 ℃ and 80 ℃. Each press indicates that the set heating temperature increases or decreases by 1 ℃. Generally, the water temperature for workpiece cleaning is about 60 ℃.

一旦溫度選中后,按溫度加溫ON鍵,加溫鮮紅色顯示燈會亮,表達剛開始加溫,顯示屏剛開始顯示信息精確測量當今器皿內的具體溫度。當溫度超過所設置的溫度時加溫鮮紅色顯示燈會滅掉,溫度電加熱器會終止加溫。

Once the temperature is selected, press the temperature heating on key, the heating bright red display light will be on, indicating that the heating has just started, and the display screen has just started to display the information to accurately measure the specific temperature in today's utensils. When the temperature exceeds the set temperature, the heating bright red display light will be off, and the temperature electric heater will stop heating.

當溫度降到低于您設定的溫度時,溫度、水位、時間、功率顯示器上顯示 059 010 020 100,溫度加熱器會自動加熱,加熱紅色指示燈會亮。當清洗槽內水溫超過10℃時,溫度、水位、時間、功率顯示器上顯示 011 010 020 100 ,表示可設定超聲波動作時間和超聲波功率，溫度超過規定溫度的80℃時溫度顯示器閃爍，溫度低于80℃時停止閃爍，表示可進行超聲波清洗。

When the temperature is lower than the temperature you set, the temperature, water level, time and power display will display 059 010 020 100, the temperature heater will heat automatically, and the heating red indicator will be on. When the water temperature in the cleaning tank exceeds 10 ℃, 011 010 020 100 is displayed on the temperature, water level, time and power display, indicating that the ultrasonic action time and ultrasonic power can be set. When the temperature exceeds 80 ℃ of the specified temperature, the temperature display flashes, and when the temperature is lower than 80 ℃, it stops flashing, indicating that ultrasonic cleaning can be carried out.

設定溫度是在不打開超聲波的情況下設定的。不打開時，溫度設定鍵無效。請注意，微處理器是記住的

The set temperature is set without turning on the ultrasonic. When it is not turned on, the temperature setting key is invalid. Note that microprocessors are remembered

超聲波清洗機一般在30℃-40℃下清洗效果較好，清洗液溫度越高，效果越明顯。通常，超聲波清洗機實際使用時，工作溫度為50-70℃。

Ultrasonic cleaning machine generally has better cleaning effect at 30 ℃ - 40 ℃. The higher the temperature of cleaning solution is, the more obvious the effect is. Generally, the working temperature of ultrasonic cleaning machine is 50-70 ℃.

上一篇：超聲波清洗機制造商行業有什么優勢？
下一篇：噴淋清洗機的噴頭毀壞有什么緣故？